Thanksgiving Trio Thanksgiving Trio A holiday service set to be thankful for! So versatile, this ensemble is party perfect. Fill the bowl with ice or a flameless candle to create a tiered treasure or dip for a chip & dip with one of the plates. This collection can be used as a beautifu
PTL Header Links (custom)
Follow Us
Location
Home / Projects / Home Decor / Thanksgiving Trio

Thanksgiving Trio

Thanksgiving Trio

Thanksgiving Trio

A holiday service set to be thankful for! So versatile, this ensemble is party perfect. Fill the bowl with ice or a flameless candle to create a tiered treasure or dip for a chip & dip with one of the plates. This collection can be used as a beautiful table setting with a soup bowl, dinner and salad plates.



Materials:

#15-0200 Armour Etch Glass Etching Cream.

#21-1653 ONO GIVING THANKS Stencil Sheet.

#30-2370 ONO ROMAN URN BOWL.

#60-7023 7.5 in. ROUND PLATE.

#60-7024 10.5 in. ROUND PLATE.

#08- 9606 Brushes.

#08- 9999 Gloves.

#08- 9415 Masking tape.

Soft paper towels.

Optional:

#61-3501 TWEEZERS.

#85-2109 HOBBY KNIFE.

Ruler and water soluble marker or china pencil.



DIRECTIONS:


1. Wash the item to be etched in hot, soapy dishwater and dry with a soft paper towel then wipe down design area with glass cleaner.

2. CORNICOPIA BOWL- Place the cornucopia stencil onto the glass in the desired position. Place the pumpkin stencil next to it. Avoid touching the sticky side of the stencil as oils from your hands can interfere with adhesion. Using a tweezer to hold stencil while deciding on placement location can help with this. If stencils protrude into each other's design, etch them individually, one at a time. Etching one at a time is the preferred method over extensive cutting. Go to STEP 6 and continue from there.

3. THANKSGIVING PLATES- With a ruler and a water soluble marker or china pencil (not a sharpie) draw the centerline on the back side of the plates.

4. Turn the plates right side up. Looking at the design image in the picture, begin placing the stencils along the outer edge of the plate to complete the design for one side of the plate, keeping the images between the lines on the edge of the plate. This design will be mirrored on the other half of the plate after you etch this side. Avoid touching the sticky side of the stencil as oils from your hands can interfere with adhesion. Using a tweezer to hold stencil while deciding on placement location can help with this. When possible, overlap stencil edges to prevent any gaps between them for etch cream to collect in later. If stencils protrude into each other's design, you can trim with a scissor or etch them individually, one at a time. Etching one at a time is the preferred method over extensive cutting.

5. Follow steps 6 through 10 to etch the first half of the plate. Wipe design area with glass cleaner. You may want to redraw centerline on the back of the project again. Repeat the design on the second half of the glass to mirror the first. Remember, if stencils protrude into each other's design, etch them individually, one at a time. Etching one at a time is the preferred method over extensive cutting.

6. Using a popsicle stick or other dull instrument, press the stencil down gently but firmly to prevent the cream from getting underneath during etching.

7. Cover all the glass around the stencils with masking tape, overlapping all edges. Rub and press the tape down securely. Check for exposed spaces by turning the project over and holding up to the light. Cover enough area so that none of the rinse water will touch any of the other glass while rinsing as even the small amount of etching cream in the water will permanently haze the glass.

8. Put on the rubber gloves. Load the brush with Armour Glass Etching cream. PAT the etch cream onto the stencils (do not brush it on). Apply a thick enough layer of cream to the exposed design area that you can no longer see through it. (View the directions HERE)

9. Leave the cream on for 5 minutes

10. Completely rinse off the etch cream under gently flowing temped water. Remove the stencils and masking tape and rinse again. Pat the stencils dry and return to the carrier sheet.

11. Wipe design area with glass cleaner. You may want to redraw centerline on the back of the project again. Arrange any remaining design elements into their desired location. Remember if stencils protrude into each other's design, etch them individually, one at a time. Etching one at a time is the preferred method over extensive cutting.

12. Repeat steps 6 through 10 until all desired design elements have been etched onto the glass

Materials

Directions

Article Posted: 11/03/2019 04:31:36 PM

Thanksgiving Trio
Thanksgiving Trio
Thanksgiving Trio
Phone: (800) 872-3458
SKIN WIDGIET - MINI LOGIN
Your Cart
Your Cart: Empty
Search
Email Signup
© 2020 Etchworld.com, all rights reserved worldwide.
Software: Kryptronic eCommerce, Copyright 1999-2020 Kryptronic, Inc. Exec Time: 0.084442 Seconds Memory Usage: 8.329391 Megabytes
Kryptronic