I Love Music I Love Music This design will make your glassware dance and sing! Spread the joy with this symphony of musical merriment on a plate and bowl for a harmonious ensemble. Make a set for a music lover you know as a showstopper gift. What about putting this design on
PTL Header Links (custom)
Follow Us
Location
Home / Projects / Home Decor / I Love Music

I Love Music

I Love Music

I Love Music

This design will make your glassware dance and sing! Spread the joy with this symphony of musical merriment on a plate and bowl for a harmonious ensemble. Make a set for a music lover you know as a showstopper gift. What about putting this design on our ornaments for a fundraiser?



Materials:

#15-0200 Armour Etch Glass Etching Cream.

#21-1671 Over N Over stencil-Musical notes

#08- 9606 Brushes.

#08- 9999 Gloves.

#08- 9415 Masking tape.

Soft paper towels.

Optional:

Tweezers, ruler, exacto knife and water soluble marker

DIRECTIONS:


1. Wash the item to be etched in hot, soapy dishwater and dry with a soft paper towel then wipe down design area with glass cleaner.

2. You may want to mark the centerline of your item before you begin. With a ruler and a water soluble marker (not a sharpie) draw the centerline on the back side of the item. This makes it easier to create your design in the location you want it on the project.

3. Apply any lettering or word stencils first, overlapping the edges where they meet. Avoid touching the sticky side of the stencil as oils from your hands can interfere with adhesion. Using a tweezer to hold stencil while deciding on placement location can help with this.

5. Choose stencils for your first row and place on a diagonal going around the glass. You may need to use individual stencils more than once to complete a row. You can also use parts of a stencil design by covering over the unwanted design features with masking tape or by trimming the stencil with scissors. If stencils overlap into each other's design, you can trim with a scissor or etch them individually, one at a time.

5. Using a popsicle stick or other dull instrument, press the stencil down gently to prevent the cream from getting underneath during etching.

6. Cover all the glass around the stencils with masking tape, overlapping all edges. Check for exposed spaces by turning the project over and holding up to the light. Cover enough area so that none of the rinse water will touch any of the other glass while rinsing as even the small amount of etching cream in the water will permanently haze the glass.

7. Put on the rubber gloves. Load the brush with Armour Glass Etching cream. PAT the etch cream onto the stencils (do not brush it on). Apply a thick enough layer of cream to the exposed design area that you can no longer see through it. (View the directions HERE)

8. Leave the cream on for 5 minutes

9. Completely rinse off the etch cream under gently flowing temped water. Remove the stencils and masking tape and rinse again. Pat the stencils dry and return to the carrier sheet.

10. Wipe design area with glass cleaner. You may want to redraw centerline on the back of the project again. Arrange all remaining design elements into their desired location. Remember, you can use parts of a stencil design by covering over the unwanted design features with masking tape or by trimming the stencil with scissors. If stencils overlap into each othe's design, etch them individually, one at a time.

11. Repeat steps 5 through 9 until all desired design elements have been etched onto the glass

Materials

Directions

Article Posted: 06/13/2019 12:55:10 PM

I Love Music
Phone: (800) 872-3458
SKIN WIDGIET - MINI LOGIN
Your Cart
Your Cart: Empty
Search
Email Signup
© 2020 Etchworld.com, all rights reserved worldwide.
Software: Kryptronic eCommerce, Copyright 1999-2020 Kryptronic, Inc. Exec Time: 0.078815 Seconds Memory Usage: 8.326927 Megabytes
Kryptronic