Last Fling Last Fling Party time for the bride to be! Create before you celebrate for a party piece that doubles as a memento. Our Bachelorette Party stencil sheet is packed with enough party elements to design from brim to base for a party that?Äôs dusk to dawn!
PTL Header Links (custom)
Follow Us

Last Fling

Last Fling

Last Fling

Party time for the bride to be! Create before you celebrate for a party piece that doubles as a memento. Our Bachelorette Party stencil sheet is packed with enough party elements to design from brim to base for a party that?s dusk to dawn!



Materials:

#15-0200 Armour Etch Glass Etching Cream.

#21-1648 ONO BACHELORETTE PARTY Stencil Sheet.

#30-2373 ONO 20 oz. WINE GLASS Stencil Sheet.

#08- 9606 Brushes.

#08- 9999 Gloves.

#08- 9415 Masking tape.

Soft paper towels.

Optional:

#61-3501 TWEEZERS.

#85-2109 HOBBY KNIFE.

Ruler and water soluble marker or china pencil.



DIRECTIONS:


1. Wash the item to be etched in hot, soapy dishwater and dry with a soft paper towel then wipe down design area with glass cleaner.

2. You may want to mark the centerline of your item before you begin. With a ruler and a water soluble marker or china pencil (not a sharpie) draw the centerline on the back side of the item. This makes it easier to create your design in the location you want it on the project.

3. Apply the word stencils first. Place the widest words stencil where the glass is the widest. Add the other stencils with words next, overlapping the edges where the stencils meet. Avoid touching the sticky side of the stencil as oils from your hands can interfere with adhesion. Using a tweezer to hold stencil while deciding on placement location can help with this.

4. Place all other design elements into their desired location. You can use parts of a stencil design by covering over the unwanted design features with masking tape or by trimming the stencil with scissors. If stencils overlap into each other?s design, you can trim with a scissor or etch them individually, one at a time. Etching one at a time is the preferred method over extensive cutting.

5. Using a popsicle stick or other dull instrument, press the stencil down gently but firmly to prevent the cream from getting underneath during etching.

6. Cover all the glass around the stencils with masking tape, overlapping all edges. Rub and press the tape down securely. Check for exposed spaces by turning the project over and holding up to the light. Cover enough area so that none of the rinse water will touch any of the other glass while rinsing as even the small amount of etching cream in the water will permanently haze the glass.

7. Put on the rubber gloves. Load the brush with Armour Glass Etching cream. PAT the etch cream onto the stencils (do not brush it on). Apply a thick enough layer of cream to the exposed design area that you can no longer see through it. (View the directions HERE)

8. Leave the cream on for 5 minutes

9. Completely rinse off the etch cream under gently flowing temped water. Remove the stencils and masking tape and rinse again. Pat the stencils dry and return to the carrier sheet.

10. Wipe design area with glass cleaner. You may want to redraw centerline on the back of the project again. Arrange any remaining design elements into their desired location. Remember, you can use parts of a stencil design by covering over the unwanted design features with masking tape or by trimming the stencil with scissors. If stencils protrude into each other?s design, etch them individually, one at a time. Etching one at a time is the preferred method over extensive cutting.

11. Repeat steps 5 through 9 until all desired design elements have been etched onto the glass

Materials

Directions

Article Posted: 10/18/2019 03:35:01 PM

Last Fling
Phone: (800) 872-3458
SKIN WIDGIET - MINI LOGIN
Your Cart
Your Cart: Empty
Search
Email Signup
© 2020 Etchworld.com, all rights reserved worldwide.
Software: Kryptronic eCommerce, Copyright 1999-2020 Kryptronic, Inc. Exec Time: 0.089354 Seconds Memory Usage: 8.326897 Megabytes
Kryptronic