Gotta Keep Rollin' Gotta Keep Rollin' Gotta Keep Rollin' Rollin' Rollin' is the baker's mantra. Capture their spirit for your kitchen with this cheeky design. We used a large flour canister out of a set of kitchen canisters for practicality and fun. Put on mixing bowls and cu
PTL Header Links (custom)
Follow Us
Location
Home / Projects / Home Decor / Gotta Keep Rollin'

Gotta Keep Rollin'

Gotta Keep Rollin'

Gotta Keep Rollin'

Gotta Keep Rollin' Rollin' Rollin' is the baker's mantra. Capture their spirit for your kitchen with this cheeky design. We used a large flour canister out of a set of kitchen canisters for practicality and fun. Put on mixing bowls and cutting boards for a complete kitchen decor set!



Materials:

#15-0200 Armour Etch Glass Etching Cream.

#21-1674 Over N Over stencil- WHAT'S COOKING

#21-1680 Over N Over stencil- FARM FRIENDS

#21-1645 Over N Over stencil- REVERSE MR MRS

#08- 9606 Brushes.

#08- 9999 Gloves.

#08- 9415 Masking tape.

Soft paper towels.

Optional:

Tweezers, ruler, exacto knife and water soluble marker

DIRECTIONS:


1. Wash the item to be etched in hot, soapy dishwater and dry with a soft paper towel then wipe down design area with glass cleaner

2. You may want to mark the centerline of your item before you begin. With a ruler and a water soluble marker (not a sharpie) draw the centerline on the back side of the item. This makes it easier to create your design in the location you want it on the project

3. Place a line of checkerboard along the bottom of the item, the right facing baker at the top corner and the rolling pin, on an angle, over the bottom checkerboard and the large empty label stencil. Unless you purchased 2 sheets of the What's Cooking stencil, you will need to etch these first. Avoid touching the sticky side of the stencil as oils from your hands can interfere with adhesion. Using a tweezer to hold stencil while deciding on placement location can help with this.

4. Using a popsicle stick or other dull instrument, press the stencil down gently to prevent the cream from getting underneath during etching.

5. Cover all the glass around the stencils with masking tape, overlapping all edges. Check for exposed spaces by turning the project over and holding up to the light. Cover enough area so that none of the rinse water will touch any of the other glass while rinsing as even the small amount of etching cream in the water will permanently haze the glass.

6. Put on the rubber gloves. Load the brush with Armour Glass Etching cream. PAT the etch cream onto the stencils (do not brush it on). Apply a thick enough layer of cream to the exposed design area that you can no longer see through it. . (View the directions HERE)

7. Leave cream on for 5 minutes

8. Completely rinse off the etch cream under gently flowing temped water. Remove the stencils and masking tape and rinse again. Pat the stencils dry and return to the carrier sheet.

9. Wipe design area with glass cleaner. You may want to redraw centerline on the back of the project again. Place the baker into position followed by the line of checkerboard at the top of the item. Place the rolling pin, on an angle, next to the first one.

10. Cut out the space between the empty labels in the stencil from the Reverse Mr. & Mrs. Sheet and place them over the checkerboard. Remove the letters you want from the Reverse Mr. & Mrs. Sheet and place them in the center of the empty labels. Tweezers are helpful with this. Press them down gently but firmly with a clean gloved finger.

11. Repeat steps 4 through 8 until all desired design elements have been etched onto the glass

Materials

Directions

Article Posted: 11/03/2019 04:51:25 PM

Gotta Keep Rollin'
Phone: (800) 872-3458
SKIN WIDGIET - MINI LOGIN
Your Cart
Your Cart: Empty
Search
Email Signup
© 2020 Etchworld.com, all rights reserved worldwide.
Software: Kryptronic eCommerce, Copyright 1999-2020 Kryptronic, Inc. Exec Time: 0.081732 Seconds Memory Usage: 8.327599 Megabytes
Kryptronic